Journal of Water and Soil Science
علوم آب و خاک
jwss
Agriculture
http://jstnar.iut.ac.ir
0
user
2476-3594
2476-5554
10.47176/jwss
fa
jalali
1392
3
1
gregorian
2013
6
1
17
63
online
1
fulltext
fa
تعیین مکان مناسب پرتابکننده روی سدهای لاستیکی
Determining the Best Place of Installation for Deflector in Rubber Dams
عمومی
Ggeneral
پژوهشي
Research
سد لاستیکی عبارت از جسم استوانهای خوابیدهای است که در عرض کانالها، رودخانهها و تاج سدها قرار میگیرد و از هوا یا آب یا ترکیبی از هر دو پر می-شود. سدهای لاستیکی ممکن است با پرتابکننده یا بدون پرتابکننده ساخته شوند. پرتابکننده زائدهای مثلثی یا مستطیلی شکل است که در بدنه پاییندست سد نصب میشود. هدف از نصب پرتابکننده جدا کردن تیغه آب از بدنه سد لاستیکی و جلوگیری از تماس مجدد آب با بدنه است. در این تحقیق 4 مدل فیزیکی مربوط به سدهای لاستیکی مورد بررسی قرار گرفت. پرتابکنندهها نیز با توجه به ارتفاع مدل و نسبت و در دو شکل مثلثی و مستطیلی با طول 25 سانتیمتر ساخته شده و در سه زاویه 30، 45 و 60 درجه مورد آزمایش قرار گرفتند. پس از تجزیه و تحلیل مشاهدات آزمایشگاهی، با توجه به پروفیلهای پرتاب آب و طول آن، زاویه نصب 45 درجه مناسبتر از گزینههای 30 و 60 درجه انتخاب گردید. همچنین برداشت-های آزمایشگاهی و رابطه ارائه شده در این تحقیق با روابط ارائه شده توسط سایر محققین مورد مقایسه قرار گرفت. همبستگی نزدیک مقادیر نشاندهنده صحت آزمایشها و روابط میباشد.
Rubber dam body is a lying cylinder that lies in the width of channels, rivers and weir crests and is filled with water or air or a combination of both. Shape of this structure is one of the obvious features that does not change in the path of rivers or dam spillways. Rubber dams may be with or without deflectors. Deflector is a triangular or rectangular fin that is installed down the stream of the dam. The purpose of installing a deflector is separating the water from the rubber dam body and avoiding the reattachment between the water and dam body. In this study, four Physical models of rubber dams and deflectors were made at height and ratio of h/p=0.05 in 2 triangular and rectangular shapes and 25 cm length. Experiments were carried out in three different angles (30-45-60). After all the analyses and experiments were done according to the water napes profile and their lengths, it was observed that the 45 degree is more suitable than 30 and 60 degrees. In addition, experimental data and presented equation in this study were compared with the past equations, the results of which were close, showing the validity of the experiments and equations
سد لاستیکی، پرتابکننده، طول پرتاب
Rubber Dam, Deflector, Length of Impact
151
164
http://jstnar.iut.ac.ir/browse.php?a_code=A-10-1357-3&slc_lang=fa&sid=1
S.B. Sarvarinezhad
سید بهنام سروری نژاد
sbsnsarvari@yahoo.com
000319475328460018071
000319475328460018071
Yes
M. Bina
محمود بینا
000319475328460018072
000319475328460018072
No
A. Moradi
ایوب مرادی
000319475328460018073
000319475328460018073
No
H. Golayj
حسن گلیج
000319475328460018074
000319475328460018074
No